Lineaarse libisemisüksuse lühitutvustus ja süsteemi kirjeldus:
◎Linear sliding units are also called linear rails, sliding rails, linear guides, linear sliding rails. They are used in linear reciprocating motion applications. They have a higher rated load than linear bearings, and can bear a certain torque at the same time, which can be used under high load conditions. Realize high-precision linear motion.
Lineaarne libisemisüksus on jagatud ruudukujuliseks kuuliga lineaarseks libisemisüksuseks, kahe-teljelise südamikuga lineaarseks libisemisüksuseks ja ühe-teljeliseks lineaarseks libisemisüksuseks.
Mandril nimetatakse seda lineaarseks liuguriks ja Taiwanis üldiselt lineaarseks juhikuks või lineaarseks liuguriks.
Lineaarse liikumisjuhi funktsioon on toetada ja juhtida liikuvaid osi, et teha edasi-tagasi lineaarne liikumine etteantud suunas. Sõltuvalt hõõrdumise olemusest võib lineaarsed liikumisjuhikud jagada libisevateks hõõrdejuhikuteks, rull-hõõrdejuhikuteks, elastseteks hõõrdejuhikuteks ja vedeliku hõõrdejuhikuteks.
◎Linear bearings are mainly used in automated machinery, such as machine tools imported from Germany, paper bowl machines, laser welding machines, etc., of course, linear bearings and linear shafts are used together. Linear sliding units are mainly used for accuracy requirements comparison On the high mechanical structure, the slider-makes the movement change from a curve to a straight line. The new guide rail system enables the machine tool to obtain rapid feed speeds. In the case of the same spindle speed, rapid feed is the characteristic of the linear sliding unit. The linear sliding unit is the same as the flat guide rail. It has two basic elements; one as a guide is a fixed element, and the other is a moving element. Since the linear sliding unit is a standard component, it is a machine tool manufacturer. The only thing to do is to process the plane of a mounting rail and adjust the parallelism of the rail. Of course, in order to ensure the accuracy of the machine tool, a small amount of scraping of the bed or column is essential. In most cases, the installation is relatively simple.
Juhtsiin kui juhik on karastatud terasest, mis asetatakse paigaldustasandile peale peenlihvimist. Võrreldes lamedate juhtsiinidega, on lineaarsete libisevate sõlmede ristlõike geomeetria{0}} keerulisem kui tasastel juhtsiinidel. Keerukuse põhjuseks on see, et juhtsiinidel on vaja töödelda sooni, mis hõlbustavad libisevate elementide liikumist. Soonte kuju ja arv sõltub tööpingi nõuetest. Täidetud funktsioon. Näiteks: Juhtrööpasüsteemi, mis kannab nii lineaarset jõudu kui ka õõnestavat momenti, võrreldakse juhtrööpaga, mis kannab ainult lineaarset jõudu. Disain on väga erinev.
There is no intermediate medium between the moving element and the fixed element of the linear sliding unit, but a rolling steel ball. Because the rolling steel ball is suitable for high{{0}}speed motion, has a small friction coefficient and high sensitivity, it can meet the working requirements of moving parts, such as the tool holder and carriage of the machine tool. The basic function of the fixed element (guide rail) of the linear sliding unit system is like a bearing ring. The bracket for mounting the steel ball is shaped like a "v". The bracket wraps the top and both sides of the rail. In order to support the working parts of the machine tool, a set of linear sliding unit has at least four supports. Used to support large working parts, the number of brackets can be more than four. When the working parts of the machine tool move, the steel balls circulate in the groove of the bracket, and the wear of the bracket is distributed to each steel ball, thereby prolonging the service life of the linear sliding unit. In order to eliminate the gap between the bracket and the guide rail, the preload can improve the stability of the guide rail system and the preload can be obtained. It is to install an oversized steel ball between the guide rail and the bracket. The diameter tolerance of the steel ball is ±20 microns, with 0.5 micron increments. The steel balls are screened and classified and installed on the guide rails respectively. The size of the preload depends on the force acting on the steel balls. If the force acting on the steel ball is too large, the steel ball will withstand the preload for too long, which will increase the movement resistance of the bracket. There is a balance problem here; in order to improve the sensitivity of the system and reduce the movement resistance, the preload must be reduced accordingly, and in order to improve the movement accuracy and the retention of precision, it is required to have sufficient preload negative numbers, which are contradictory two. aspect.
Kui tööaeg on liiga pikk, hakkab teraskuul kuluma ja teraskuuli eelkoormus hakkab nõrgenema, mille tulemusena väheneb tööpingi tööosade liikumistäpsus. Kui soovite säilitada esialgset täpsust, peate asendama siini kronsteini või isegi asendama siini. Kui rööpasüsteemil on eelkoormuse efekt. Süsteemi täpsus on kadunud ja ainus võimalus on veereelemendid välja vahetada.
Juhtrööpasüsteemi konstruktsioon püüab saavutada suurima kontaktpinna fikseeritud elemendi ja liikuva elemendi vahel. See mitte ainult ei paranda süsteemi kandevõimet, vaid suudab taluda ka vahelduva lõikamise või gravitatsiooniga lõikamise tekitatud löögijõudu, hajutada jõudu laialdaselt ja laiendada kandevõimet. Jõupiirkond. Selle saavutamiseks on juhtsiinide süsteemi jaoks ette nähtud erineva kujuga sooned. Esinduslikke on kaks. Ühte nimetatakse Gedai tüübiks (terakaare tüüp), kuju on poolringi pikendus ja kontaktpunkt on tipp; teine Liik on kaarekujuline{0}}ja võib samuti mängida sama rolli. Olenemata konstruktsioonist, on sellel ainult üks eesmärk ja püüdke saavutada rohkem veeremiskuuli raadiuse kontakti juhtsiiniga (fikseeritud element). Süsteemi tööomadused määrab: kuidas veerevad elemendid kontaktrööpaga kokku puutuvad, mis on probleemi võti.